Trade
Plumbing / Heat pumps / Photovoltaics
Location
Ruse, Bulgaria
UIC
207093802

WaterWarmthEnergy

One contractor across all three, instead of coordinating three trades around the same building.

Start a project
Technician inspecting pipework beside an outdoor heat-pump unit at a modern home
Technical installation, representative imageRuse / BG
01 ServicesWhat each one needs

Each entry gives what the system does, what the building has to provide for it, and what is established on site.

Three systems, one contractor

PLB

Plumbing systems

Function
Carries water to the fixtures that use it and takes waste away
Site needs
Access to the runs and a working supply and drainage connection
Surveyed
Route of the existing pipework, its condition and its sizing
HPS

Heat-pump systems

Function
Moves heat instead of burning fuel, for heating, cooling and hot water
Site needs
A position for the unit, an electrical supply and a way to distribute heat
Surveyed
Heat demand of the building and what the existing emitters can carry
PVS

Photovoltaic systems

Function
Converts daylight into electricity for use in the building
Site needs
Unshaded roof or ground area, a position for the inverter, a connection point
Surveyed
Orientation, shading over the day and the capacity of the connection
02 ApproachThree things that decide

Technical work starts with the property, not with a preselected package

01

Building fabric

Insulation, glazing and how airtight a building is set its heat demand. That figure, not the floor area, is what a heat pump has to be sized against.

02

What is already installed

Pipe sizing, emitters, the consumer unit and the incoming supply decide whether a system is replaced, extended or left in place. Those are four different jobs on the same property.

03

The electrical connection

A heat pump and a photovoltaic array both land on the electrical supply, and on what the connection permits where the grid is involved. It is the constraint that most often changes a plan.

03 ProcessSurvey before specification

Only the second step needs access to the property.

A clear route from enquiry to installation

  1. 01

    Describe the property

    Location, what is installed now, and what the new system has to do. Photographs of the existing plant, the emitters and the meter or consumer unit answer most of the first questions.

  2. 02

    Define the scope

    A site visit establishes what the rows above list as surveyed. What is in the job, and what is not, follows from what it finds.

  3. 03

    Arrange the work

    Once the scope is clear, the installation can be planned around the site and the agreed project.

04 CompanyOne legal representative

A Ruse-based company for building systems

A single-member company working in the city and the surrounding area, for households and businesses alike. The registration details opposite can be checked against the Bulgarian Commercial Register.

Legal name
VSG 80 EOOD
UIC
207093802
Registered address
3 Petko Karavelov Street
7000 Ruse, Bulgaria
Director
Veselin Georgiev
05 QuestionsRadiators, roofs, sequencing

Common questions

Will a heat pump work with the radiators already in the house?

Not always as they stand. A heat pump runs at a lower flow temperature than a gas or solid-fuel boiler, so the same radiator gives out less heat than it did before. Whether the existing emitters are enough depends on the heat demand of each room, which is why that is established before a system is specified rather than after.

Does a photovoltaic array need a south-facing roof?

South is the best case, but east and west generate too. The difference shows in the shape of the day rather than in whether the array works: an east and west split spreads output across morning and afternoon instead of concentrating it around midday. Shading across the day usually matters more than orientation does.

Is there any advantage to doing more than one system at once?

Mostly in sequencing. Heating and hot water are part of the plumbing, so those two are one job more often than not, and where an array goes in as well the electrical work happens once rather than twice. It changes the order of the work, not the specification: each system is still sized on its own.

Ready?

Start a
project